Hp Laserjet 3050 Toner Refill
How To Properly Remanufacture Your HP 2500-2550 Color Toner Cartridges In Just 45 Easy Steps
Did you know?
Hewlett Packard Color LaserJet 2500 smart technology print cartridges offer great print quality and reliable performance for affordable, professional quality color printing. It also has new advanced toner, ease-of-use features and smart technology has been a plus to the end consumer. Here are your Step-by-Step "How-to-Remanufacture" the HP 2500 Color LaserJet Toner Printer Cartridge Instructions: Let's get straight to the point, no beating around the bush during this lecture. First, you will need the necessary Tools & Supplies Required: Tools & Supplies Required: #2 Phillips Head Screwdriver (tool) #0 Phillips Head Screwdriver (tool) Small Flat-blade Screwdriver (tool) Silicon (tool) X-acto Knife (tool) Cotton Swab (tool) 99% Isopropyl Alcohol (supply) Lint-free Cloth (supply) Toner Seal Here you will also be provided with the OEM (original equipment manufacturer) information: HP 2500: Part Numbers: C9700A (black), C9701A (cyan), C9702A (yellow)and C9703A (magenta) OEM Gram Load: 1100 grams Yield @ 5% coverage: 20, 000 pages / min:32 Resolution: 1200dpi (dots per inch) Below are your 45 easy steps to know how to remanufacture your HP 2500 LaserJet C9700A (black), C9701A (cyan), C9702A (yellow), & C9703A (magenta) toner cartridges. Step #1: Gently set your toner cartridge on your workstation with the toner hopper contact end plate facing you. Step #2: Take your #2 Phillips-head screwdriver and remove the two black screws from the end plate. Note: The screw located just below the developer roller is longer than the other screws on the cartridge. Make sure the correct screw is used when reassembling the cartridge otherwise the screw can jam and cause an invalid toner cartridge. Step #3: Now, take out your #0 Phillips-head screwdriver and remove the small screw from the contact end plate. Step #4: You should be able to slide the end plate away from the toner cartridge. Step #5: Simply rotate the cartridge at 180 degrees. Remove the 2 screws holding the gear housing end cap to the toner hopper. Step #6: Gently slide the gear housing end cap from the toner hopper. Step #7: Remove the 5 gears from the end of the cartridge leaving the toner hopper agitator drive gear. Step #8: The developer and roller end plate is held in place by 2 screws. Step #9: Take your #0 Phillips-head screwdriver and remove the small silver screw. Step #10: You can now slide the developer roller end plate from the side of the cartridge. Step #11: Whatever you do - DO NOT lose the round bearing that sits inside the developer end plate. Step #12: Rotate the cartridge at 180 degrees. Remove the screw holding the developer roller end plate to the hopper. Step #13: Remove the end plate while holding the developer roller. Step #14: Remove the developer roller. Next, remove the developer roller bearings from the ends of each roller. Note: Again, whatever you do - DO NOT lose the round bearing that sits inside the end plate. Note: Be sure to clean the developer using a lint-free cloth along with some alcohol. Step #15: In order to lift the top cover of the hopper, you need to lift the back of the cover off the positioning post located on the backside of the hopper. Step #16: At this point you can lift off the top cover. Step #17: Simply remove the 2 screws holding the doctor blade. Step #18: By Joseph Mercado - Joseph Mercado is an open-minded, leading self-motivator based upon positive-self influence. The personal philosophy of Joseph is what drives him into the next century of success. His teachings ignite his m...Next page: Cheap Hp Laserjet Toner
Bookmark/Share This Page:
|
|
|
|
